Guide
Plumbing Permits and Plumbing Inspections: What Needs a Permit and What Gets Inspected
Clearing a clog, fixing a leak and swapping a faucet need no plumbing permit. New or moved pipes and gas piping do, and so does a water heater in most places. Replacing a toilet or sink in place depends on the city. The line item by item, then the rough-in and final inspections, from the model code and Portland, Philadelphia, Minneapolis, Boston, Chicago, Las Vegas, Grand Rapids and Seattle.
You need a plumbing permit when you add, move or replace pipes or run gas piping, and in most places when you install or replace a water heater. Under the model code and in most cities we read, you do not need one to clear a clog, stop a leak or replace a faucet. Replacing a toilet or sink in the same spot is where cities split: Grand Rapids and Las Vegas let you do it without a permit, Portland requires a permit for any fixture, and Boston lists a Plumbing Permit for it that only a licensed contractor can get.
The next step: find your job in the table below. If it needs a permit where you live and pipes are being added or opened up, plan for two inspections, one before the pipes are covered and one at the end, and do not close a wall or ceiling until the first one passes. Your building department’s own page is linked from our verified index.
The short version, job by job
| Job | Permit? | Whose words |
|---|---|---|
| Clear a clogged drain | No under the model code | Model code: “The clearing of stoppages or the repairing of leaks in pipes, valves or fixtures” |
| Fix a leak without replacing pipe | No under the model code | Model code: “The stopping of leaks in drains, water, soil, waste or vent pipe” |
| Replace a faucet, a valve or the parts inside a toilet tank | No in Philadelphia, Minneapolis and Las Vegas | Philadelphia: “This includes replacing faucets, valves, and parts” |
| Pull a toilet and set the same one back | No under the model code | Model code: “the removal and reinstallation of water closets” |
| Replace a toilet, sink or tub with a new one in the same place | Depends on the city | See the next section |
| Replace a water heater | Yes in most places we read | Minneapolis: “Replace or install a water heater” |
| Move a fixture, or add a new one | Yes | Las Vegas: “Alter piping inside a wall, ceiling or beneath a floor” |
| Replace a section of concealed drain or supply pipe | Yes under the model code | ”such work shall be considered as new work and a permit shall be obtained” |
| Run or alter a gas line | Yes | Las Vegas: “Install, alter or repair gas piping between the meter and any appliance” |
| Replace a sewer line or water service | Yes | Portland: “Install or replace water service lines” |
North Carolina is the exception on replacement: its state law exempts same-size plumbing replacements in a house when the job costs $40,000 or less. Elsewhere the part of a sewer line under the street can need a second permit from public works or the sewer utility; our sewer line guide covers both.
What the model code exempts
Most local rules start from the International Residential Code, a model code that states and cities adopt, often with their own changes. Its general rule requires a permit to “erect, install, enlarge, alter, repair, remove, convert or replace any electrical, gas, mechanical or plumbing system.” It then exempts exactly two kinds of plumbing work.
The first is stopping a leak: “The stopping of leaks in drains, water, soil, waste or vent pipe; provided, however, that if any concealed trap, drainpipe, water, soil, waste or vent pipe becomes defective and it becomes necessary to remove and replace the same with new material, such work shall be considered as new work and a permit shall be obtained and inspection made as provided in this code.”
Read that twice, because it is the line most people get wrong. Tightening a fitting or patching a leak is exempt. Cutting out a bad section of pipe behind a wall and putting in new pipe is not; the code calls that “new work.”
The second is clearing and small repairs: “The clearing of stoppages or the repairing of leaks in pipes, valves or fixtures, and the removal and reinstallation of water closets, provided such repairs do not involve or require the replacement or rearrangement of valves, pipes or fixtures.” A water closet is a toilet. You may lift one to clear a blockage or replace the wax ring and set it back. Under the model code’s wording, putting in a different toilet is a “replacement” of a fixture, which is why cities had to write their own rule for it.
The code also closes the repair loophole from the other side. Ordinary repairs do not include “addition to, alteration of, replacement or relocation of any water supply, sewer, drainage, drain leader, gas, soil, waste, vent or similar piping.”
Replacing a toilet, sink or tub: where cities split
No permit. Grand Rapids: “If you’re only replacing a faucet, sink, toilet, or similar fixture, a plumbing permit is not required. We require permits for any plumbing work beyond that.” Las Vegas lists “Repair/replace a sink” and “Repair/replace a toilet” among work that needs no permit, and states the general test: “Replacement of plumbing fixtures in the same location with a similar fixture and materials provided no work is done other than the replacement of the fixture, the tail piece and/or the trap and provided the work does not penetrate fire-resistive rated construction, including a fire-resistive rated concrete slab.” See Las Vegas plumbing permits.
No permit for some fixtures, a permit for others. Minneapolis lets you replace “Sink faucets and water closets” and “Dishwashers and garbage disposals” in a one- or two-family home without a permit, on the condition that “You do not alter or replace the existing water supply line or plumbing piping system.” Its permit page still requires a plumbing permit to “Replace or install fixtures, like sinks, showers and tubs.” So in Minneapolis a new toilet is exempt and a new bathtub is not.
A permit, but a simple one. Philadelphia exempts only “Minor repairs with the same material,” “Removing and re-installing toilets, if no pipes or fixtures will be replaced or moved,” and “Stopping leaks and clearing stoppages.” A new fixture needs a permit, but “Replacement of any number of fixtures with fixtures of the same kind” qualifies for an EZ permit, which does “not require you to submit plans.”
A permit, every time. Portland requires a plumbing permit to “Install or replace plumbing fixtures (like toilets, sinks, showers, tubs, or dishwashers).” The only work it lists as exempt is to “Fix or maintain existing plumbing fixtures or parts” and to “Replace plumbing-related items that don’t use water (like a toilet seat).” Boston lists a Plumbing Permit “For replacing or installing a sink, toilet, shower, or bathtub when no other work needs to be done, such as opening up walls.”
A dishwasher shows how far apart two cities can be: replacing one is exempt in Minneapolis and on Portland’s plumbing permit list.
Water heaters and gas lines
A water heater is permit work in most of the cities we read. Las Vegas requires a permit to “Install or replace a water heater or water softener.” Minneapolis and Portland both list replacing a water heater as permit work, and Grand Rapids requires a permit for “adding or working on a water heater.” Chicago is the exception among the cities we read: in a residential building up to four stories, no building permit is needed for “Repairing or replacing (in-kind) a hot water heater,” where in-kind means “new materials, objects, or elements of the same type, size, and shape.” Our guide to water heater permits goes through that job on its own.
Running or altering gas pipe is permit work in the cities we read that address it. Las Vegas names the jobs people do not expect: a “gas line for a BBQ, add a fire pit, pool heater.” Hooking up an appliance is less uniform. Minneapolis requires a plumbing permit to “Connect gas appliances like stoves, dryers or fireplaces to gas piping,” while Grand Rapids says “You don’t need one for installing or removing gas appliances (like stoves and dryers).” Minneapolis also lists “Capping an open gas line” among work that may not need a permit. The model code’s own gas exemptions are narrow: portable appliances, such as “Portable heating, cooking or clothes drying appliances,” and “Replacement of any minor part that does not alter approval of equipment or make such equipment unsafe.”
For the whole gas job, including which permit carries gas piping in 73 offices, capping a line and the pressure test, see our guide to gas line permits.
Emergencies: fix it first, apply the next day
A burst pipe does not wait for a permit office. The model code’s emergency rule says: “Where equipment replacements and repairs must be performed in an emergency situation, the permit application shall be submitted within the next working business day to the building official.” Minneapolis says the same in plain words: “Emergency repairs can be done before you apply for a permit. You must apply within the next working business day.”
The emergency does not make the permit go away. Las Vegas lists “Emergency repair, alteration, or replacement of damaged or leaking concealed piping” among work that requires a permit.
A whole-house repipe is the clearest case of pipe replacement counting as new work; that guide covers the pressure test and the grounding question when copper is replaced with plastic.
Which office issues the permit
Usually the city or county building department, but not always. In Seattle, plumbing permits do not come from the city’s building department at all: “Whenever you are going to install, relocate, or change a plumbing or gas piping system, Seattle and King County codes require that you obtain a permit. Public Health has jurisdiction in Seattle and unincorporated King County.” The agency’s list of places it covers also names Clyde Hill. If you live in any other King County city, “you will need to get your plumbing and gas piping permits from that city’s building department.” See Seattle plumbing permits, and our guide to which office actually issues your permit.
Who is allowed to pull it
- Boston: “Plumbing permits are available to licensed contractors only.” The page is blunt about it: “If you’re a homeowner, you must hire a licensed contractor to apply for the permit and complete the work.”
- Philadelphia: any property owner or authorized agent can apply, but “A licensed master plumber must oversee plumbing work.”
- Portland: “Homeowners can do their own plumbing work,” as long as the homeowner is “the recorded property owner by the County and not an LLC.”
- Seattle, Clyde Hill and unincorporated King County: “The permit issued to a homeowner is an authorization for the homeowner to do the plumbing.”
- Grand Rapids: “As a homeowner, you’re able to do any plumbing work in your home with a permit. If you’re a landlord, you’ll need a licensed and registered plumbing contractor.”
If you hire a plumber, the permit should be in the plumber’s name. Boston requires it: “The permit applicant must be the contractor performing the work.” Our guide to who pulls the permit explains why that protects you.
Our guide to whether a homeowner can pull a plumbing permit sorts 56 offices by who may pull one: owner-occupants, owners after an exam, or licensed plumbers only.
The plumbing inspections
A job that adds or opens up piping means two visits. A simple fixture replacement has nothing to rough in and may need only the final; Boston’s page describes one inspection, requested “Once your work is finished.”
Rough-in, before anything is covered. The model code requires that “Rough inspection of plumbing, mechanical, gas and electrical systems shall be made prior to covering or concealment, before fixtures or appliances are set or installed.” Portland tells homeowners what that means: “Call for an inspection before covering any piping with floor, wall, or ceiling.” The piping includes water, sewer, stormwater and the vent system, and “The inspector will check that your plumbing is installed to code and doesn’t leak.” Then the instruction that matters most: “Do not cover work until approved.”
Final, after the fixtures are in. Portland: “After completing all plumbing work, you must get a final inspection to close the permit.” Without it, the permit stays “under inspection” and is never closed, and “Permits expire if there are more than 180 days between inspections.” The model code’s version: “Final inspection shall be made after the permitted work is complete and prior to occupancy.”
How you get the inspector to the house varies more than the inspections do.
- Where Public Health Seattle and King County inspects, a request is not an appointment: “Inspections are not scheduled for a specific time of the day,” and the agency says to “Plan for several business days after requesting an inspection.”
- In Boston, “An inspector will contact you within 48 hours to schedule and confirm your inspection,” and “The licensed contractor must be onsite during the inspection.”
- Portland lists the three reasons work does not get approved: “no access - the inspector could not inspect the work,” “incomplete work” and “code violations.” The first one is avoidable: be home, and leave the work uncovered and reachable.
If an inspection fails, you fix what the inspector listed and call for a re-inspection. Our guide to what happens after a failed inspection covers re-inspection fees and deadlines, and what inspectors check covers the other inspections on a larger job.
What the permit costs
Three cities’ published pricing:
- Boston: “There is a $20 application fee plus $5 for each fixture, such as toilets and sinks.”
- Philadelphia: a $100 filing fee that is “nonrefundable and is applied toward the final permit fee,” with the permit fee set by whether the job is new construction, an alteration, or “Repair and replacement.”
- Portland: fees “are based on the fixtures and the work being done.”
For your own city, open its plumbing page from our plumbing permit index; each page there carries the fee details we verified for that place.
For three common jobs priced line by line on nine fee schedules, see our guide to what a plumbing permit costs.
If you start before the permit, or never get one
Boston states the consequence on the permit page itself: “Do not begin work before your permit is issued. If you do, Inspectional Services may: charge double the permit cost, or issue a building code violation.” It also gives the permit a clock: “You must start work within six months after your permit is issued.”
Unpermitted plumbing sits behind finished walls and floors, and that is what makes it costly to put right. Las Vegas warns that work found later “can require an engineering evaluation and report, possible destructive testing, removal of wall coverings, and replacement plumbing, electrical or other various elements of the un-permitted construction.” Our state pages on building without a permit list the penalty and the after-the-fact permit route in each state we cover.
Method
Every rule above was read on November 11, 2026 on the building or health department’s own page or handout, or in the 2024 International Residential Code on ICC’s digital codes site, all linked below. Each quotation was matched by machine against the text of the page it came from. Many states enforce a state plumbing code that is not the residential code, and your state may enforce a different edition, so the list your own department publishes is the one that governs your house.
Sources
- 2024 International Residential Code, Chapter 1, read on ICC Digital Codes: R105.1 (when a permit is required), R105.2 (work exempt from permit, the two plumbing items and the gas items), R105.2.1 (emergency repairs), R105.2.2 (ordinary repairs) and R109.1.2 and R109.1.6 (rough and final inspections). (accessed )
- City of Portland, Oregon, Residential Plumbing Permits: work that does and does not need a permit, who can do the work, how fees are set, and the rough-in and final inspections. (accessed )
- City of Philadelphia, Get a Plumbing Permit: the three kinds of work that need no permit, EZ permits without plans, the master plumber requirement and the filing fee. (accessed )
- City of Minneapolis, Plumbing permits: the list of work that needs a plumbing permit. (accessed )
- City of Minneapolis, Construction work exempt from permit: the plumbing work allowed without a permit in one- and two-family dwellings, its conditions, and the emergency repair rule. (accessed )
- City of Boston, Install or Replace a Sink, Toilet, Shower, or Bathtub: a Plumbing Permit even when no other work is done. (accessed )
- City of Boston, Plumbing Permit: licensed contractors only, the $20 plus $5 per fixture fee, the six-month start rule, the penalty for starting early, and the inspection steps. (accessed )
- City of Chicago Department of Buildings, What Types of Work Do Not Require a Building Permit?: the Plumbing Work section, including in-kind water heater replacement. (accessed )
- City of Las Vegas Building and Safety, When Do I Need a Permit?: plumbing work that requires a permit, including gas piping, and the fixture repairs and replacements that do not. (accessed )
- City of Grand Rapids, Michigan, overview of permits for home renovation projects: the plumbing permit line and who may do the work. (accessed )
- Public Health Seattle and King County, plumbing and gas piping applications and permits: when a permit is required, the homeowner permit, and which places the agency covers. (accessed )
- Public Health Seattle and King County, inspections for plumbing and gas piping installations: how inspection requests are scheduled and how long to allow. (accessed )
Get rule-change alerts
We catch permit rule and fee changes in our verification passes and post them to the rule tracker. Get them by email instead.
We may send occasional verified rule-change notes for your area; unsubscribe anytime. See our privacy policy.