Guide
Do You Need a Permit to Run, Move or Cap a Gas Line?
Running, extending or moving gas piping takes a permit in all 73 offices whose verified rule names gas piping, and capping a line when an appliance comes out often does too. Which permit gas work goes on, who may do it, the pressure test the code requires, and what the gas company asks to see.
Yes. A new gas line, an extension to a grill or a range, or moving a line to a new spot is permitted work in all 73 offices whose verified rule in our dataset names gas piping, and none of them exempts it apart from a short meter carve-out in Detroit. Capping a line is the question with a real split: some offices want a permit to take a gas appliance out, and some do not ask for one when the appliance is a range or a dryer. What every version of the job shares is the end of it: before gas flows through new or altered pipe, the code calls for an inspection and a pressure test.
- Run, extend or move a line
- Permit requiredall 73 offices whose rule names gas piping
- Cap a line when an appliance comes out
- Depends on the officeArlington County and Chesterfield County, VA: yes; Grand Rapids, MI: no for stoves and dryers
- Which permit it goes on
- Plumbing 29, mechanical 24, a separate gas permit 16, both trade rows 4
- Pressure test in the model code
- 1.5 times working pressure, at least 3 psig, for 10 minutes2024 IRC G2417.4
- Fees read on November 18, 2026
- $99 flat; $137 plus $27 per outletAurora, CO; Seattle and King County, WA
If you are hiring this out, send the fitter this before you agree a price: “Please confirm that your quote includes the gas permit, the pressure test and inspection, and the meter or regulator change if the gas company needs one, and tell me which permit type you will file under.” The last part matters because, as the table below shows, the name of the permit changes from one office to the next.
The code starts from “remove”
The International Residential Code, the model code that states and cities adopt and amend, does not treat gas work as minor. Its permit rule covers anyone who intends “to erect, install, enlarge, alter, repair, remove, convert or replace any electrical, gas, mechanical or plumbing system.” Removing is in that list. The 2024 edition then exempts three pieces of gas work, and the two that come up in a house are “Portable heating, cooking or clothes drying appliances” and “Replacement of any minor part that does not alter approval of equipment or make such equipment unsafe.” (The third is portable fuel-cell appliances not connected to fixed piping or to the power grid.) A new run of pipe is none of these, and neither is a line moved six feet to reach a new range.
Local offices adopt and amend that model, so read your own rule. In our dataset, the offices that address gas piping say the same thing in different words: Contra Costa County, California’s handout requires a plumbing permit “to replace, add or extend any gas piping”; Oklahoma City says gas services and gas piping systems always need one; Overland Park, Kansas, issues a separate Gas Line Permit for a new line or an extension, with a pressure test at inspection. The one carve-out we found is narrow: Detroit’s list of exempt mechanical work includes gas piping limited to 10 feet and 6 fittings when a gas meter is changed or relocated.
Which permit you will be filing
This is where a homeowner gets sent to the wrong counter. We sorted the 73 offices whose verified rule names gas piping by the permit that carries it:
| Gas piping goes on | Offices | Examples from our dataset |
|---|---|---|
| The plumbing permit | 29 | Las Vegas, Scottsdale, Tampa, New Castle County (DE), Seattle and King County |
| The mechanical (HVAC) permit | 24 | Portland (OR), Minneapolis, Pittsburgh, Detroit, Boise |
| A separate gas permit | 16 | Birmingham, Baltimore County, Worcester, Saint Paul, Chesterfield County (VA) |
| Named in both plumbing and mechanical rules | 4 | DeKalb County (GA), Fort Wayne, Sacramento County, Cleveland |
Two agencies behind that table are not building departments at all. In Montgomery and Prince George’s counties in Maryland, gasfitting is permitted and inspected by WSSC Water, the regional sanitary commission. In Seattle and unincorporated King County, plumbing and gas piping permits come from Public Health, not the building department. Public Health prices a gas piping permit at $137 plus $27 per outlet (2026 schedule). Aurora, Colorado, sits at the other end: its 2026 flat-rate list puts “Gas Pipe Installation or Modification” at $99.
Capping a line: three offices, three answers
When a gas range, dryer or fireplace comes out and nothing replaces it, the open outlet has to be closed. The model code is plain about the end state: “Gas outlets that do not connect to appliances shall be capped gastight.” Whether closing it needs a permit depends on the office, and three that publish their rule show the spread:
- Arlington County, Virginia: “A plumbing/gas permit is required for adding, removing, or relocating fixtures, appliances, or piping for all plumbing and gas work.” Taking an appliance off the line is removal.
- Chesterfield County, Virginia: gas permits are required for “Removing, replacing or installing any gas appliances or equipment, including piping, gas logs, water heaters, furnaces.” The county then lists the appliances that do not need one for replacement: “cook tops, stoves, ranges and dryers.” Its carve-out is worded for replacing those four, so ask before you remove one without a replacement.
- Grand Rapids, Michigan: a mechanical permit is required for water heaters, furnaces, boilers and similar equipment, but “You don’t need one for installing or removing gas appliances (like stoves and dryers).”
Capping a stub behind a range is small work with a large failure mode, which is why the offices that permit it want a licensed hand or an inspection. If yours does not require a permit, the outlet still has to end up capped gastight, with the appliance valve shut, and a leak check is cheap insurance.
Who may do the work
Gas is where homeowner permission runs out in several offices. Portland, Oregon, says “Homeowners can do their own mechanical work,” gas piping included, as long as the homeowner is the recorded owner and not an LLC. Several offices that allow owners to do their own plumbing draw the line at gas, in their rules as verified in our dataset: New Castle County, Delaware, lets owner-occupiers pull a plumbing permit, but not for gas piping; Bernalillo County, New Mexico’s homeowner plumbing test does not cover gas piping; Corpus Christi, Texas, lets homeowners plumb their homestead but requires new or altered natural gas systems to be installed by a state licensed plumber. WSSC Water does not let homeowners install gas appliances at all. Manchester, New Hampshire, goes the other way and lets a resident single-family homeowner apply for gas work.
If your office does not let you do it, the permit has to be pulled by whoever is licensed for it, and that is often a plumber or a licensed gas fitter, not the general contractor.
The pressure test and the inspection
The 2024 IRC requires new piping to be inspected and tested “Prior to acceptance and initial operation.” The numbers it sets:
- Test pressure: “not less than 1 1/2 times the proposed maximum working pressure, but not less than 3 psig.”
- Duration: “not less than 10 minutes.”
- Pass: the piping holds the pressure “without showing any evidence of leakage”; a drop on the gauge counts as a leak unless something else explains it.
- Small repairs: “Minor repairs and additions shall not be required to be pressure tested provided that the work is inspected and connections are tested with a noncorrosive leak-detecting fluid or other approved leak-detecting methods.”
Chesterfield County’s inspection table shows how that plays out on a house: a rough-in and a final for new or altered piping, and a separate groundwork inspection “for any gas piping installed below grade including under a concrete slab.” If you are trenching to a grill, a fire pit or a pool heater, the trench stays open until it is seen. The appliance end of that line, including the fire code distances for a fire pit, is in our guide to fire pit and outdoor kitchen permits.
Two more code points belong on the inspector’s list for new work. Corrugated stainless steel tubing (CSST) that is not listed as arc resistant has to be bonded to the electrical grounding system (G2411.2). And every appliance needs its own shutoff valve in the same room, within 6 feet of it (G2420.5.1).
The gas company’s part
Past the meter, the buried pipe is often the owner’s to look after, and federal pipeline rules make the gas company say so in writing: an operator that does not maintain a customer’s buried piping must notify the customer that “The operator does not maintain the customer’s buried piping” and that it “should be” periodically inspected for leaks and, if metallic, for corrosion (49 CFR 192.16). The same rule tells customers that when digging near buried gas piping, it “should be located in advance, and the excavation done by hand.”
Two things can bring the utility into a homeowner project. If the new appliances add up to more gas than the meter was sized for, the meter or regulator may need to be changed, and that is the utility’s equipment, not the fitter’s. And on new or upgraded service, a utility can ask for proof of the local inspection before it sets a meter: PSE&G in New Jersey asks that the local inspection authority affix “the yellow ‘piping pressure test’ sticker” after a pressure test inspection.
Before the line is buried or the wall is closed
- Confirm which permit your office files gas work under (plumbing, mechanical or gas) and who is allowed to pull it.
- Ask the fitter for the test pressure and duration they will use, and be home for the inspection.
- For an outdoor run, call 811 before digging and leave the trench open for the groundwork inspection.
- When capping a line, ask whether your office wants a permit for the removal, and keep the record either way.
- Keep the finaled permit with your house papers. A buyer’s inspector will ask about a new gas line, and so may your insurer after a claim.
Method
The five model-code, county and city pages quoted here, the two fee schedules and the federal rule were read on November 18, 2026. The count of 73 comes from our dataset: every verified row whose rule mentions gas piping, a gas line or a gas permit, after leaving out rows that mention gas only inside Florida’s $7,500 exemption, only in a shed or pool rule, only in a code adoption, or only in a water heater exemption. Each of the 73 was then sorted by hand into the permit its own rule names; rows that say only “gas work” without naming piping, a line or a gas permit (Miami-Dade County, for one) are not in the 73. Offices cited from the dataset are named as such; each one’s pages on this site show when its rule was last read. We have not surveyed utilities beyond PSE&G, and their meter and inspection rules vary. The model code chapters were read on ICC’s public code site (the January 2024 version of the 2024 IRC) early on November 18; the site later began refusing automated readers, so they could not be read a second time that day.
Do You Need a Permit to Run, Move or Cap a Gas Line?: figures as of 28 Sep 2026, 137 jurisdictions. Now 178.
Sources
- 2024 International Residential Code, R105.1 (a permit to install, alter, remove or replace a gas system) and R105.2 (the two gas items exempt from permit). (accessed )
- 2024 International Residential Code, Chapter 24 Fuel Gas: G2415.15 outlet closures, G2417 inspection and pressure testing, G2411 bonding. (accessed )
- Chesterfield County, Virginia, Residential Permits and Inspections Processes: projects that require a gas permit, the appliances exempt on replacement, and the gas inspections table. (accessed )
- Arlington County, Virginia, Plumbing / Gas Permit page: adding, removing or relocating fixtures, appliances or piping. (accessed )
- City of Grand Rapids, Michigan, Overview on Zoning and Permits for Home Renovation Projects: the mechanical permit and the gas appliance carve-out. (accessed )
- City of Portland, Oregon, Residential Mechanical Permits: gas piping indoors and outdoors between the meter and appliances, homeowner work, inspections. (accessed )
- Public Health Seattle and King County, Plumbing and Gas Piping Program fees effective January 1, 2026: gas piping permit $137 plus $27 per outlet. (accessed )
- City of Aurora, Colorado, 2026 Flat Rate Fee Permits: Gas Pipe Installation or Modification at $99 each. (accessed )
- PSE&G (New Jersey), Mandatory Local Inspections: the pressure test inspection and the yellow piping pressure test sticker before a gas meter is set. (accessed )
- 49 CFR 192.16, Customer notification: gas operators that do not maintain a customer's buried piping must say so in writing. (accessed )
Get rule-change alerts
We catch permit rule and fee changes in our verification passes and post them to the rule tracker. Get them by email instead.
We may send occasional verified rule-change notes for your area; unsubscribe anytime. See our privacy policy.