PermitNotebook / Guides

Guide

Do You Need a Permit to Run Electricity to a Shed?

Almost always: a new circuit to a shed is permitted electrical work even where the shed itself needs no permit, and in 20 of the 48 offices whose shed rule mentions wiring or utilities, power also takes away the shed's own exemption. The rare exception, the trench depths, disconnect and GFCI rules inspectors check, and who may pull the permit.

Almost always. A new circuit to a shed is electrical work, and nearly every office we cover requires an electrical permit for it, including the many that require no permit for the shed itself. We found one office whose code may allow a single small circuit without one, and one county with no residential electrical permit at all (both below). The size limits in shed exemptions (120 or 200 square feet in most places) decide whether the building needs a permit. They do not cover the wire. In 20 of the 48 offices whose shed rule mentions wiring or utilities, power does more than add an electrical permit: it takes away the shed’s own exemption, so a shed small enough to need nothing becomes permitted work once it is wired.

Electrical permit for a new circuit
Required almost everywhereSioux Falls: ask; its code reads both ways
Power also ends the shed exemption
20 of 48 officesthe shed then needs its own permit too
Shed stays exempt, wiring permitted separately
22 of 48 offices
Burial depth, direct burial cable
24 inchesNEC 300.5; some offices allow 12 for a GFCI-protected 120 volt circuit
Inspection before backfill
Yes; the trench is inspected open

Before you buy wire or rent a trencher, look up two rules on your office’s site: the shed exemption (does it say “no electrical” or “no utilities”?) and who may pull an electrical permit for a house you own and live in. Those two answers decide how many permits you need and whether you can do the work yourself.

Two ways offices treat a wired shed

We read the shed rules of the 178 building offices we cover. In 48 of them the rule as published on this site says something about wiring or utility connections. Most of those split into two groups. (If the wired shed will be an office, studio or bedroom, the use matters as much as the wire; see our guide to using a shed as a room.)

The shed keeps its exemption; the wire needs its own permit. In 22 offices, the building exemption stands and the circuit is permitted on its own. Overland Park, Kansas, puts it plainly in its accessory structure guidelines: “Any electrical wiring or gas piping to an accessory structure requires a permit regardless of the size of the structure.” Anchorage, Little Rock, Tampa, Omaha, Albuquerque, Milwaukee, Prince William County and Prince George’s County are in this group too.

Power takes away the shed’s exemption. In 20 offices the exemption itself is written for a shed without utilities, so wiring it means the shed needs a building permit as well as the electrical work. In the rules as verified in our dataset, Dallas, one of the largest cities we cover, exempts a small storage building only if it contains no utilities. The Arizona offices show the pattern clearly: Phoenix, Mesa, Scottsdale and unincorporated Maricopa County exempt a small shed only when it has no electrical, plumbing or mechanical connections, Gilbert only when it has no electrical or plumbing, and Peoria requires a permit for any shed with utilities. Los Angeles, San Jose, Sacramento County, Las Vegas, Indianapolis, Pinellas County, Hawaii County and Thurston County, Washington, write the same condition into their exemptions.

Where power ends the exemption, the shed is reviewed like any permitted accessory building: a site plan showing setbacks, sometimes construction drawings, and inspections of the structure as well as the wiring. Gwinnett County, Georgia, folds both into one permit: its accessory building handout says “The Building Permit may include electrical installation. A separate “electrical only” permit is not required,” and requires the electrical rough-in inspection to pass before the final.

Two offices go further. Chandler, Arizona, does not allow power at all in what its zoning code calls a storage shed: section 35-2203, printed in the city’s homeowner permit manual, says a storage shed “cannot be served by any utility (electricity, gas or water)”. A wired outbuilding there is a different class of accessory building with its own rules. And the Town of Hempstead, New York, asks for a notarized affidavit of no plumbing or electrical with a shed filing.

A possible exception. Sioux Falls, South Dakota, lists its electrical permit triggers by quantity. Section 150.213(b)(1) of its code requires a permit for “Installation of five or more outlets, switches, receptacles, fixtures, or two new electrical circuits 30 amps or less, or one new electrical circuit greater than 30 amps”, and one new 20 amp circuit with a light, a switch and an outlet is under that line. But (a)(1) of the same section makes it unlawful to install or connect any regulated electrical system “without first obtaining a separate electrical permit for each building or structure”. Read together, the code does not plainly let you wire a separate building without a permit, so ask Sioux Falls Building Services before relying on the quantity list. It is the only office in our data with a quantity rule like it. Unincorporated Harris County, Texas, is a different case: it publishes no residential electrical permit at all.

If you are in Maryland, our Maryland shed guide quotes each county’s own wording on the electrical permit for a shed, including who in Maryland may pull it.

What the inspector checks

The National Electrical Code sets the rules for a circuit to an outbuilding, and the offices that publish homeowner checklists print the parts that matter most. The Saint Paul, Minnesota, checklist for detached garages under the 2023 code is one of the clearest, and the same articles govern a shed.

  • Burial depth. Under NEC 300.5, Saint Paul lists the minimum cover to the top of the wiring method as 6 inches for rigid metal or intermediate metal conduit, 18 inches for PVC conduit and 24 inches for direct burial cable (UF or USE). Humboldt County, Nevada, prints the same 18 and 24 inch figures for conduit and direct burial wire. Some offices print a shallower line for exactly the circuit most sheds need: Boulder County, Colorado, lists “Residential branch circuits 120 volts or less w/ GCIF protection” (its spelling of GFCI) at 12 inches. Ask your office which line of NEC Table 300.5 it applies before you dig.
  • Protection where it comes out of the ground. Saint Paul’s checklist requires rigid metal, intermediate metal or Schedule 80 PVC conduit above grade, and says direct burial cable “shall be protected by a raceway to at least 18” below grade.”
  • One circuit or feeder. “A detached garage shall only be served by one branch circuit or feeder” (NEC 225.30, on the Saint Paul checklist). For a shed, that usually means either one circuit from the house panel or a feeder to a small panel in the shed.
  • A disconnect at the shed. NEC 225.31 and 225.32 require a disconnecting means for the conductors supplying the building, readily accessible outside or immediately inside it. Mesa County, Colorado, tells homeowners that for “out buildings that are not a garage, one circuit installation is permitted with a snap switch for a disconnect.”
  • Grounding. A building supplied by a feeder, or by a branch circuit over 20 amps, needs its own grounding electrode system (NEC 250.32(A), Saint Paul), which in practice is usually two ground rods. Humboldt County requires the ground and neutral to be separated in a sub-panel.
  • GFCI protection. Humboldt County: “All garage and outbuilding outlets shall be GFCI (ground fault circuit interrupter) protected.”

The trench is inspected open. Saint Paul’s checklist cites Minnesota Rule 3801.3770: wiring in a trench “must be inspected before it is concealed”, and whoever backfills first pays to uncover it. Humboldt County says it inspects all underground installations. Plan the job so the inspector can see the wire or conduit at the bottom of the trench before any soil goes back in.

Your office may have adopted a different edition of the electrical code, or local amendments. Its own checklist, where it publishes one, is the version an inspector will use.

Who may pull the permit

That depends on the state and often the city. Many offices let a homeowner pull an electrical permit for a single-family home they own and live in, sometimes after a short test or an affidavit; others allow only a licensed electrician to pull it. Our guide to whether a homeowner can pull an electrical permit sets out the rule in 11 states and the city exams and affidavits on top of them. Gwinnett County, for example, requires a subcontractor affidavit from a state licensed electrician, and from a homeowner doing the work, before it will schedule inspections.

Before you dig

  1. Read your office’s shed exemption for the words “electrical”, “utilities” or “mechanical”. If they are there, the shed needs a building permit once it is wired.
  2. Find out who may pull the electrical permit for your house, and whether the office wants one permit or two.
  3. Decide what the shed needs: one 20 amp circuit for lights and an outlet, or a feeder to a small panel for tools or a heater. The answer changes the wire size, the grounding and the fee.
  4. Have buried utility lines marked before you dig the trench.
  5. Schedule the trench inspection before you backfill, then the final once the outlets, switch and cover plates are in.
  6. Keep the finaled permit. A wired shed is one of the things a buyer’s home inspector notices, and the permit is the proof it was inspected.

If the shed is already wired without a permit, our guide to electrical work that needs a permit explains how offices handle work that is already done.

Method

Every office document cited above was downloaded and read on November 18, 2026. The two groups are our own classification of the 48 shed permit rows in our dataset whose published rule (summary, when needed, or threshold condition) mentions electrical work or utility connections: 20 make the absence of electrical or utility connections a condition of the shed exemption, 22 keep the exemption and require the trade permit, and six (Chandler; the Town of Hempstead; Hernando County, Florida; Pima County and Tucson, Arizona; Berkeley County, West Virginia) do not fit either group cleanly. More rows mention a trade permit in their research notes; we counted only the published rule. Each office’s own shed page on this site quotes its rule. The code articles are cited as printed in the Saint Paul, Humboldt County and Mesa County handouts, not from the National Electrical Code itself.

Do You Need a Permit to Run Electricity to a Shed?: figures as of 28 Sep 2026, 137 jurisdictions. Now 178.

Sources

Get rule-change alerts

We catch permit rule and fee changes in our verification passes and post them to the rule tracker. Get them by email instead.

We may send occasional verified rule-change notes for your area; unsubscribe anytime. See our privacy policy.